Practicing Network Automation with GNS3

Practicing Network Automation with GNS3

In an earlier post I took a look at how to setup EVE-NG to get access to virtualized network devices and topologies. This post is going to take a look at how to setup GNS3 systems to allow access.

In the overall topology that is a "home" network sits a device that supports a routing protocol, usually either OSPF or BGP. What is known to work at an inexpensive price point is the Ubiquiti EdgeRouter X.

GNS3 Setup

This post is not a post on how to setup GNS3, it is meant to help you start to access devices. This tutorial is running a GNS3 VM on a remote host. Take a look at the GNS3 docs on how to install GNS3 specifically.

GNS3 Configuration

The topology item used to create the connection to the production network is the device type of Cloud. Add a cloud with the general connection and the device will have connectivity to your local network.

Next setup a router (in this instance using a Cisco vIOS image - licensed item). Connect that device to the cloud that was added to the topology. In this particular setup, DHCP is being used.

Screen Shot 2020-11-01 at 11.38.05.png

Router Configuration

rtr-edge#show run interface GigabitEthernet0/0
Building configuration...

Current configuration : 110 bytes
!
interface GigabitEthernet0/0
 ip address dhcp
 duplex auto
 speed auto
 media-type rj45
 no cdp enable
end

With the device getting an address, the device also gets a floating default static route imported to match the DNS request:

rtr-edge#show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
       a - application route
       + - replicated route, % - next hop override, p - overrides from PfR

Gateway of last resort is 192.0.2.1 to network 0.0.0.0

S*    0.0.0.0/0 [254/0] via 192.0.2.1
      192.0.2.0/24 is variably subnetted, 2 subnets, 2 masks
C        192.0.2.0/24 is directly connected, GigabitEthernet0/0
L        192.0.2.163/32 is directly connected, GigabitEthernet0/0

Verify that you have access to the Internet by using ICMP to test.

rtr-edge#ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 13/16/18 ms

Setup Automation

By using OSPF you are able to setup networks and advertise them back into your "production"/"home" network. With the network being advertised you can then setup your hosts with addressing that would have access from the network.

It is recommended that you test SSH/API connectivity into the GNS3 environment manually.

Summary

With the tools of GNS3, EVE-NG, Cisco CML, and VRNetLab you have significant choice in looking at tools that will help you to level up your skills in Network Automation.

Hope that this may help you out in some way!

ko-fi

Josh